AccuQuilt GO! Wonky Heart 6" Finished
|
|
|
|
The GO! Wonky Heart makes it easy and fun to play with fabric color and block layout to create your own quirky heart shapes. This fabric cutting die is part of our BOB (Block on Board) series that allows you to build an entire block with just one die. Use your GO! Die Cutter and 10" precut squares. There is no need to trim as you go because of the GO! Wonky Heart is designed for easy piecing.
Wonky Heart Free Pattern
Find Fabric Dies for Your Pattern
COMPATIBLE WITH THESE FABRIC CUTTERS: Go!, and the Go! Big
Cut Size Measurements: Cuts One each of
- A Shape 2 11/16"W x 1 7/8"H (6.8 cm x 4.8 cm)
- B Shape 2 3/4"W x 4 7/8"H (7 cm x 12.4 cm )
- C Shape 2 5/8"W x 2 3/16"H (6.7 cm x 5.6 cm)
- D Shape 3 13/16"W x 3 3/16"H (9.7 cm x 8.1 cm)
- E Shape 3 7/8"W x 3 11/16"H (9.8 cm x 9.4 cm)
- F Shape 3 9/16"W x 1 7/8"H (9.0 cm x 4.8 cm)
- G Shape 4 1/4"W x 3 11/16"H (10.8 cm x 9.4 cm)
- H Shape 4 1/4"W x 2 1/4"H (10.8 cm x 5.7 cm)
- I Shape 3"W x 3 5/16"H (7.6 cm x 8.4 cm)
- J Shape 2 7/8"W x 4"H (7.3 cm x 10.2 cm)
Use GO! dies with your GO! and GO! Big Fabric Cutters to cut precise, accurate shapes in just seconds.
Features and Benefits:
- Cut so much more in less time -- Cut up to 6 layers of 100% cotton fabric at once
- Easiest to use -- Simply place die on cutter, then fabric and cutting mat on top
- Get accurate cuts every time -- No slipping rulers or mistakes
- Create quilts you never thought you would -- AccuQuilt makes cutting curvy classic quilt patterns a snap
- Save fabric with Two Tone Foam -- Get more out of your fabric by placing it only over the shape you want to cut
- Safe to use -- No blades come anywhere near your fingers
- No more math -- Geometric shapes are designed with an accurate 1/4" seam allowance in the design
- Quilt more, clip less -- No more clipping all those dog-eared corners
- Quick and easy applique -- Apply fusible web to fabric prior to cutting
Storage: Organize GO! dies with AccuQuilt GO! Die Storage Rack (55115).
Die Tips:
- With some fabrics, after cutting, a thread or two will remain where die blades meet. Snip threads with scissors.
- Use cutting mats that match the size of each die.
- For best results, cut with die blades running under roller at an angle. Do not cut with blades parallel to roller.
- Blades on some dies are positioned at an angle. Align fabric to edge of shape, not edge of die board.
- Some dies feature specially designed corners to aid in alignment and pre-cutting.
- For fast applique, apply fusible web to fabrics, then cut shapes with dies.
- Use good quality fabric to reduce fabric stretch.
- It's always a good idea to test cut one shape before cutting many shapes to ensure fabric orientation is correct.
Use adhesive roller to clean lint and thread from dies. After each use, with the die pick provided with the cutter, remove any threads imbedded between blades and foam. It's normal for threads to get caught where blades meet in a die. Remove with tweezers or die pick. Die blades never need to be sharpened.